China EWD330 Electronic Drain Valve Solenoid Valve Service Maintenance Kit Manufacturer, Supplier, Factory

Atlas Copco 1901067022,The function of the oil suction valve of Atlas Copco air compressors: The oil suction valve is a key component of the lubrication system of air compressors. Its core function is to ensure the smooth supply of lubricating oil and maintain the stability of the system. By controlling the intake of lubricating oil, through opening or closing actions, it regulates the flow of lubricating oil entering the suction pipeline from the oil tank, ensuring that the friction parts such as the rotor and bearings of the air compressor receive sufficient lubrication. Preventing oil backflow, when the air compressor is shut down or unloaded, the oil suction valve closes, preventing the high-pressure lubricating oil in the oil tank from flowing back through the suction pipeline to the oil tank, avoiding waste of oil and system contamination. Maintaining system pressure, in coordination with pressure maintaining valves and other components, maintaining the stable pressure in the oil and gas tank, providing continuous pressure support for the lubrication system, ensuring that the lubricating oil can be smoothly transported to all lubrication points. Filtering impurities to protect equipment, some oil suction valves are equipped with filters or used in combination with suction filters to filter metal particles, dust impurities in the lubricating oil, preventing them from entering the air compressor main unit, reducing component wear.

The Atlas Copco 100 HP Oil Injected Air Compressors GA55 of the GA series is one of the ideal choices for producing compressed air and reducing energy consumption. GA55 Atlas Copco Rotary Screw Air Compressors series: follow China Taike Trading online distribution network to check out GA55P, GA55FF, GA55+, GA55+ FF (air cooling & water cooling options are available).

Atlas Copco 2906049800，The accessories in the air compressor service kit are precisely matched according to the design parameters of the equipment, effectively filtering air impurities, keeping the lubricating oil clean, separating oil from the compressed air, controlling the intake volume and pressure, and preventing faults caused by component failure. The high-quality intake valve diaphragm can prevent air leakage and avoid the continuous decrease in pressure due to inability to load after disengagement; the compatible oil-gas separator can control the oil content in the exhaust to an extremely low level, avoiding pollution of the post-treatment equipment and the gas-using equipment. The original or high-quality components in the service kit use wear-resistant and corrosion-resistant materials (such as high-precision rotors, high-quality bearings, and oil seals), which can reduce the wear of core components such as the main unit, rotor, and bearing. For example, a high-quality oil filter can filter metal particles and impurities in the lubricating oil to prevent them from entering the main unit and wearing the rotor, thereby extending the lifespan of the main unit; the compatible coolant can effectively lower the exhaust temperature, avoiding the deterioration of the lubricating oil due to high temperature and reducing the failure of the cooling system. Compared with using inferior components, in the long run, it can significantly reduce the frequency and cost of maintenance.

Maintenance and Common Issues of 40°C Thermostat for Atlas Copco Air Compressors Regular Calibration: After long-term use, temperature drift may occur. It is recommended to calibrate with a thermometer annually to ensure accurate triggering at 40°C. Cleaning and Maintenance: If the sensing part is covered with oil or dust, it will affect the sensitivity of temperature measurement. It is necessary to wipe it regularly (operate in power-off state). Common Faults: Temperature Trigger Deviation: This may be due to the aging of the sensing element. Replacement of the same model thermostat is required. Contact Adhesion: Causes the cooling equipment to run continuously or fail to start. Check the contact condition and replace it if necessary.

The electromagnetic valve maintenance kit for Atlas Copco EWD330 electronic drainage valve is applicable for maintenance suggestions. Applicable models: Only applicable to Atlas Copco EWD330 type electronic drainage valve. Before purchase, it is necessary to confirm the production batch and electromagnetic valve specification of the drainage valve to avoid model mismatch. Maintenance timing: When the drainage valve shows slow operation, abnormal drainage (such as no drainage or continuous drainage), abnormal noise from the electromagnetic valve, or air leakage, it may be necessary to repair the electromagnetic valve. At this time, this kit can be used to replace the worn parts. Installation note: It is recommended to operate by professionals. Before maintenance, cut off the power and air source, assemble in accordance with the original factory manual specifications, ensure that the components are installed properly, and avoid functional failure or safety hazards due to improper assembly.

The combined effect of the air filter and the oil filter assembly in Atlas Copco air compressors The air filter purifies the incoming air, reducing impurities that enter the system and indirectly reducing the burden on the oil filter assembly; The oil filter assembly separates the oil from the compressed air, ensuring the quality of the outgoing air and simultaneously recovering the lubricating oil and reducing operating costs. The decline in the performance of either component will affect the efficiency of the air compressor: blockage of the air filter will result in insufficient air intake and increased energy consumption; failure of the oil filter assembly will cause the compressed air to contain excessive oil, polluting downstream equipment or products.