China Air Compressor Controller Parts Manufacturer, Supplier, Factory

Troubleshooting and Replacement Suggestions: Common Issues and Solutions: Stalling or Leakage: Causes unstable pressure and increased energy consumption. It is recommended to disassemble and clean or replace directly (it is suggested to replace the entire set to avoid matching issues between new and old components). Reduced Adjustment Precision: Mostly due to wear of sensors or valve cores. Replacement of the original kit is required and recalibration is necessary. Installation Tips: After replacement, parameter matching through the controller (such as setting pressure upper and lower limits) is necessary to ensure normal system linkage.

Failure causes and maintenance suggestions for Atlas Copco Air compressor O-ring Common failure causes: Long-term high-temperature aging leads to reduced elasticity, wear or scratches (such as impurities entering the sealing surface), improper installation (such as twisting, being too tight), incorrect selection (material not suitable for the medium or temperature). Maintenance precautions: Regularly inspect the condition of the O-ring. Replace it promptly if it shows signs of hardening, cracking, deformation or leakage. When replacing, clean the sealing groove and mating surface, remove oil stains, burrs and impurities. Avoid using sharp tools to scratch the O-ring during installation. If necessary, apply special lubricating grease (compatible with the medium) to assist in installation. Select matching specifications and materials for the O-ring based on the air compressor model and location.It is recommended to use original factory parts to ensure the sealing effect.

Maintenance Key Points for Worm Wheel Type Impellers in Atlas Copco Centrifugal Air Compressors Regular Inspection: Use endoscopes or shut down for disassembly to check if there are cracks, wear, deposits, or foreign object impact marks on the impeller surface. Special attention should be paid to the blade roots (stress concentration areas). Dynamic Balance Calibration: If the impeller shows slight deformation or wear after long-term operation, it may cause dynamic balance imbalance. Re-calibration is necessary to avoid excessive vibration of the shaft system. Replacement Standard: When the impeller has irreparable cracks, severe damage to the blades, or the dynamic balance cannot be adjusted to the qualified range, it is necessary to replace the original factory impeller in time to ensure the matching and operational safety of the unit.

Replacement and Maintenance Precautions If the components show signs of aging and cracking of the hose, leakage at the joints, damage to the reinforcement layer, or bulging, they must be replaced immediately to prevent leakage of high-pressure media, which could cause safety hazards or affect system operation; When replacing, it is essential to use the original Fx1050Xf type components to ensure that their dimensions, pressure resistance level, and joint sealing are consistent with the original components. Non-original components may cause installation difficulties or premature damage due to poor compatibility; During installation, pay attention to the bending radius of the hose (it must not be less than the specified value, usually 6-8 times the diameter of the hose), avoid excessive twisting or stretching, and keep away from high-temperature components and rotating parts. If necessary, use pipe clamps for fixation to reduce vibration and wear.

Replacement and precautions for the oil filter housing of Atlas Copco screw-type air compressors Part matching: It is necessary to use the original Atlas Copco housing module to ensure complete matching with the model and filter cartridge model (for example, the housing specifications of different power models of the GA series are different). Installation guidelines: Clean the internal oil stains and impurities of the housing during replacement, and check if the sealing surface is flat. The new housing needs to be properly coated with sealant (if necessary) or installed with new O-rings to avoid leakage. Tighten the filter cartridge with the specified torque to prevent over-tightening from damaging the housing threads or under-tightening causing leakage. Regular inspection: During each oil filter cartridge replacement, simultaneously check for any cracks or deformations in the housing, whether the sealing parts are intact, and ensure the reliable operation of the oil circuit system.

Based on the general accessory information for this series of models, the relevant reference number for the vent hole kit of ZT15-22 may be: Some models use a ventilation assembly with the serial number 2901111500 (including ventilation plugs, sealing rings, etc.);